최신 800-150 무료덤프 - Cisco Supporting Cisco Devices for Field Technicians
Drag and drop the actions that must be taken after installing an E-Series server from the left into order on the right.
정답:
Explanation:
In theFLDTEC course, underMaintenance and RMA Procedures, Cisco outlines a specific sequence for bringing up anE-Series server modulein an ISR router. The sequenceensures proper recognition, IOS compatibility, and network readiness:
* Power up the router and server: Ensures both components are initialized and POST begins.
* Verify that the router recognized the server: Use service-module commands or show platform to confirm server visibility.
* Load a compatible Cisco IOS image onto the ISR: The IOS must support the E-Series module to provide integration and configuration functionality.
* Connect the server to the network: Establish network connectivity for services, remote access, or deployment.
This structured approach is essential for minimizing errors duringmodular hardware upgrades or RMAsin the field.
Which mode must the console terminal of the device be in before a prewritten configuration is pasted to transfer the configuration from an old device to a new one?
정답: D
설명: (DumpTOP 회원만 볼 수 있음)
Drag and drop the steps of the boot sequence process of a Cisco device into order on the right.
정답:
Explanation:
Step 1 # Performs power-on self-test (POST)
Step 2 # Loads and runs bootstrap code (firmware)
Step 3 # Finds and loads the Cisco IOS software
Step 4 # Finds and loads the configuration
Step 5 # Runs the configured Cisco IOS software
This startup process is thoroughly described in theFLDTECcourse and alignswith Cisco's standard IOS boot process:
* POST (Power-On Self-Test):Verifies hardware functionality including memory and interfaces. This occurs immediately upon powering the device.
* Bootstrap Code Execution:Bootstrap is a small program in ROM that initiates the boot process.
* Cisco IOS Loading:Bootstrap locates and loads the IOS from flash memory or another source (e.g., TFTP).
* Configuration Loading:The router then loads the startup-config from NVRAM (if available).
* IOS Execution:Once the configuration is loaded, the device enters operational mode and executes the IOS with the loaded config.
This sequence is vital for field technicians to understand for troubleshooting boot failures or performing device recoveries.
Drag and drop the Cisco UCS components from the left onto the corresponding functionalities on the right.
정답:
Explanation:
According toFLDTEC documentation and Cisco UCS architecture guides, each of these elements plays a distinct and essential role:
Fabric Interconnects (FI)- Act as the central switching and management point for the UCS domain, connecting servers to LAN and SAN.
Virtual Interface Cards (VICs)- Installed in servers, these adapters supportvirtualization of multiple NICs and HBAs, enabling dynamic profile assignment.
Fabric Extenders (FEXs)- Extend the I/O fabric from the FI to the chassis, reducing complexity and consolidating management.
Servers- Provide the actual compute resources and run workloads. These can bebladeorrack servershoused in the UCS chassis.
This structure is critical to theCisco Unified Fabric approach, which simplifies data center management through integration and automation.
Refer to the exhibit. Which CLI show command identifies the serial number on a router?
정답: B
설명: (DumpTOP 회원만 볼 수 있음)
Which operating system powers the Cisco Nexus series of switches and is optimized formodern data center deployments?
정답: C
설명: (DumpTOP 회원만 볼 수 있음)
Drag and drop the descriptions from the left onto the corresponding IPv4 addressing modes on the right.
정답:
Explanation:
This content is aligned withIPv4 Addressing Fundamentals, detailed in the FLDTEC course underDevice Configuration and Verification:
Unicast: A unicast address uniquely identifies a single host on anetwork. This is the most common address type used for standard communication between two devices.
Broadcast: Broadcast addresses (e.g., 255.255.255.255 or subnet-specific broadcast) send traffic to all hosts in the network segment. Used for ARP requests and DHCP discovery.
Multicast: Used to deliver a packet to agroup of hostsinterested in the data, without flooding the network like a broadcast. Multicast uses addresses from the range224.0.0.0 to 239.255.255.255.
Loopback: The loopback address (127.0.0.1) is reserved for local testing, ensuring that the TCP/IP stack is working properly without needing to access the network.
Which two network design strategies in Cisco data center solutions improve fault tolerance and high availability? (Choose two.)
정답: B,D
설명: (DumpTOP 회원만 볼 수 있음)
Why is a Cisco Nexus switch typically deployed in a network?
정답: A
설명: (DumpTOP 회원만 볼 수 있음)
What is the first action that must be taken before removing a standby supervisor module from a Cisco MDS
9700 Series Switch?
9700 Series Switch?
정답: A
설명: (DumpTOP 회원만 볼 수 있음)