최신 3605 무료덤프 - Avaya Ethernet Routing Switch Implementation and Maintenance

문제1

Which protocol can be used for end-to-end detection in a network as well as for point-to-point detection?

A. VLACP

B. RSTP

C. LACP

D. MSTP

정답: A

설명: (DumpTOP 회원만 볼 수 있음)

문제2

What is a characteristic
of Routed Split Multi-Link Trunking (RSMLT)
configuration?

A. RSMI T uses priority values to distinguish between the primary and backup routers.

B. RSMLT is only configured on edge SMLT connections.

C. RSMLT is always used in conjunction with routing protocols and SMLT connections.

D. RSMLT routers are implemented with Virtual Routing Forwarding (VRF)-Lite routers.

정답: C

문제3

A campus network has been established with four Ethernet Routing Switch (ERS)
8600 switches in a switch cluster, two pairs with an Inter Switch Trunks (1ST)
running Split Multi-Link Trunk (SMLT) and Routed Split Multi-Link Trunking
(RSMLT). The traffic filters are required to block specific source IP addresses to
be forwarded through the core. How should these filters be set up?

A. Apply the filters to the edge switches and never on the switch cluster ERS 8600 switches.

B. Apply the filters to all ports that receive traffic from outside the immediate switch cluster.

C. Configure the filters on the ports first and then the 1ST.

D. Configure the filters on the 1ST first before any other ports.

정답: A

문제4

A technician is configuring a Link Aggregation connection from a stack of
Ethernet Routing Switch (ERS) 5500
lo a core pair of
ERS 8600 switches.
Which
statement
about
the correct uplink configuration is true?

A. Use unique MLT IDS for each stack of edge ERS 5500 switches

B. Enable Spanning Tree Protocol for the MLT when using it with SMLT in the core of the network.

C. Disable auto negotiation and replace it with VLACP to identify single fiber fault failure

D. Distribute uplinks across different ERS 5500 switches in the stack.

정답: D

문제5

Refer to the exhibit.
A campus network has been established with four Ethernet Routing Switch (ERS) 8600 switches in a switch cluster, two pairs with an Inter Switch Trunks (IST) running Split Multi Link Trunk (SMLT) and Routed Split Multi-Link Trunking (RSMLT). The traffic filters are required to block specific source IP addresses to be forwarded through the core. With reference to the exhibit, how should these filters be set up?

A. Configure the filters on the ports first and then the IST.

B. Apply the filters to all ports that receive traffic from outside the immediate switch cluster.

C. Configure the filters on the 1ST first before any other ports.

D. Configure and apply all the filters on the two core IST links only

정답: B

문제6

A technician wants to control the routes being added to the routing table from the BGP routing table. Which statement describes how to do this?

A. BGP accept filters are applied only to external route information.

B. BGP accept filters are applied to all routes from received by BGP peers.

C. BGP accept filters are applied to all incoming and outgoing ports.

D. BGP adds all new priority routes to the routing table.

정답: B

문제7

While
configuring
packet
capture
Tool
(PCAP),
an
Ethernet
Routing
Switch (ERS) 8600 switch has generated the following log: pcapAllocateBuffer: malloc(96 Mbs) failed Which event could have caused this log, and which course of action resolves the issue?

A. There is not enough available memory for PCAP. Try with a lower value of buffer-size.

B. The packet capturing stopped. Enable the Buffer-wrap or reset the stats.

C. The memory allocation failed to wrap. Set Pcmcia Wrap to true

D. The length of the IP frame is too long to capture. Turn on fragmentation

정답: A

문제8

A campus network requirement is to introduce Virtual Routing and Forwarding (VRF) in the existing Ethernet Routing Switch (ERS) 8600-based core. The technician has to configure VRF on the ERS 8600. Which statement represents the order for configuring a new VRF?

A. Create a VRF, create a new VLAN move the VLAN to the new VRF, and add an IP address

B. Create a VRF, create a new VLAN, add an IP address, and move the VLAN to the new VRF

C. Create a VRF, add an IP address, create a new VLAN, and move the VLAN to the new VRF

D. Create a new VLAN, add an IP address, create a VRF, and move the VLAN to the new VRI

정답: A

문제9

1ST
configuration using the
show mlt
ist info command, which IP
address should be in the
IP ADDRESS column?

A. the IP address of the ISTVLAN on the local switch

B. the management IP address of the peer switch

C. the IP address of the IST VL AN on the peer switch . the IP address of the IST on the peer switch

정답: C

문제10

A split Multi-Link Trunking (SMLT) for switch clustering is being configured.
Which statement is a configuring requirement for the SMLT?

A. CP-Limit is configured on edge switch stacks.

B. Alternate the primary paths of the SMLT connection to load balance the switch core.

C. Neighboring edge switch stacks should be connected to each other via a DMLT connection to add resilent paths in the event of an SMLT failure.

D. VLANs that are defined on the SMLT are also defined on the MLT that defines the core inter Switch Trunks (IST).

정답: D

최신 3605 무료덤프 - Avaya Ethernet Routing Switch Implementation and Maintenance

우리와 연락하기

유용한 링크

최신 업데이트