최신 NSE5_FSW_AD-7.6 무료덤프 - Fortinet NSE 5 - FortiSwitch 7.6 Administrator
Refer to the exhibit.
You just connected three FortiSwitch devices:Core-1,Core-2, andAccess-1. Core-1 and Core-2 both connect to Access-1 for redundancy. All switches are managed by FortiGate, which uses port4 as the FortiLink interface. After you enable the uplink ports on Core-2, you notice that port3 on Access-1 enters the Discarding STP state. What is the most likely cause of this behavior? (Choose one answer)
You just connected three FortiSwitch devices:Core-1,Core-2, andAccess-1. Core-1 and Core-2 both connect to Access-1 for redundancy. All switches are managed by FortiGate, which uses port4 as the FortiLink interface. After you enable the uplink ports on Core-2, you notice that port3 on Access-1 enters the Discarding STP state. What is the most likely cause of this behavior? (Choose one answer)
정답: D
설명: (DumpTOP 회원만 볼 수 있음)
FortiGate is unable to establish a tunnel with the FortiSwitch device it is supposed to manage Based on the debug output shown in the exhibit, what is the reason for the failure?
정답: C
설명: (DumpTOP 회원만 볼 수 있음)
Which LLDP-MED Type-Length-Values does FortiSwitch collect from endpoints to track network devices and determine their characteristics?
정답: C
설명: (DumpTOP 회원만 볼 수 있음)
Refer to the exhibits. An IP phone is connected to port1 of FortiSwitch Access-1. The IP phone tags its traffic with VLAN ID 20. On FortiGate, VLAN IP_Phone (VLAN ID 20) has been configured, and port1 of Access-
1 is set with VLAN 20 as the native VLAN. However, the IP phone cannot reach the network. The exhibit shows the partial VLAN configuration and the port1 configuration on Access-1.
Which configuration change must you make on FortiSwitch to allow ingress and egress traffic for the IP phone? (Choose one answer)
1 is set with VLAN 20 as the native VLAN. However, the IP phone cannot reach the network. The exhibit shows the partial VLAN configuration and the port1 configuration on Access-1.
Which configuration change must you make on FortiSwitch to allow ingress and egress traffic for the IP phone? (Choose one answer)
정답: C
설명: (DumpTOP 회원만 볼 수 있음)
Exhibit.
port24 is the only uplink port connected to the network where access to FortiSwitch management services is possible. However, FortiSwitch is still not accessible on the management interface. Which two actions should you take to fix the issue and access FortiSwitch? (Choose two.)
port24 is the only uplink port connected to the network where access to FortiSwitch management services is possible. However, FortiSwitch is still not accessible on the management interface. Which two actions should you take to fix the issue and access FortiSwitch? (Choose two.)
정답: B,D
설명: (DumpTOP 회원만 볼 수 있음)
(Full question statement start from here)
You enable Dynamic Host Configuration Protocol (DHCP) snooping on a VLAN and configure a FortiSwitch port astrustedfor DHCP snooping. What additional step is required to configure the port as trusted for Dynamic ARP Inspection (DAI)? (Choose one answer)
You enable Dynamic Host Configuration Protocol (DHCP) snooping on a VLAN and configure a FortiSwitch port astrustedfor DHCP snooping. What additional step is required to configure the port as trusted for Dynamic ARP Inspection (DAI)? (Choose one answer)
정답: B
설명: (DumpTOP 회원만 볼 수 있음)
You need to mirror traffic from a source port on Switch A to a monitoring device on Switch C. For that purpose, you're configuring Remote Switched Port Analyzer (RSPAN).1Due to the nature of RSPAN, what is the best practice when setting it up? (Choose one answer)
정답: C
설명: (DumpTOP 회원만 볼 수 있음)
Exhibit.
You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device with the configuration shown in the exhibit. did not reboot All three devices completed FortiLink manage-ment authorization successfully.
Why did the FortiSwitch device shown in the exhibit not reboot to complete the authorization pro-cess?
The management mode was set to use FortiLink mode.
You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device with the configuration shown in the exhibit. did not reboot All three devices completed FortiLink manage-ment authorization successfully.
Why did the FortiSwitch device shown in the exhibit not reboot to complete the authorization pro-cess?
The management mode was set to use FortiLink mode.
정답: D
설명: (DumpTOP 회원만 볼 수 있음)
Which two requirements must be met before FortiGate can manage a FortiSwitch stack? (Choose two answers)
정답: C,D
설명: (DumpTOP 회원만 볼 수 있음)