최신 350-080 무료덤프 - Cisco CCIE Data Center Written

A. The vNIC is currently active and uses the fabric failover peer vNIC.

B. The host to which the vNIC belongs is currently powered off.

C. There are no Ethernet uplinks that are enabled.

D. One or more of the VLANs that are assigned to the vNIC are assigned to different disjoint Layer 2 uplinks.

E. One or more of the VLANs that are assigned to the vNIC have been deleted from Cisco UCS Manager.

A. The class-all-flood and class-ip-multicast class maps are used on the Fabric Extender.

B. The Fabric Extender inherits the CoS configured on the upstream switch.

C. For a Cisco Nexus 2248PQ 10GE Fabric Extender, all fabric interfaces can be bundled into a single fabric port channel.

D. The Fabric Extender provides two user queues for its QoS support, one for all no-drop classes and one for all drop classes.

A. sparse-dense mode

B. dense-sparse mode

C. dense mode

D. sparse mode

A. The iSCSI initiator that connects to target name iqn.1987-02.com.cisco.t3 will see two LUNS as numbers 0& 4.

B. The iSCSI initiator at name iqn 1987-02.com.cisco.t2 has access to only one LUN

C. The iSCSI initiator that connects to target name iqn.1987-02.com.cisco_t3 will see two LUNS numbered as2 and 4.

D. The FC lun 0x0000 mapping to iscsi-lun 0x0000 is not permitted.

E. The iSCSI initiator and iSCSI target iqn.1987-02.com.cisco.t3 must be in the same zone before LUNS areavailable to host.

A. 6

B. 4

C. 3

D. 12

E. 2

A. A VSD is collection of interfaces that are guarded by the service virtual machine.

B. vMotion is supported for the service virtual machine and should not be disabled.

C. Service virtual machine only snoops the data and is used for monitoring purposes.

D. The show virtualservice_domainname command displays the configurations for this VSD port profile.

E. A virtual service domain (VSD) allows you to classify and separate traffic for network services.

F. Any traffic coming or going out of the VSD must go through the service virtual machine.

A. infrastructure simplification

B. centralized management for all application teams

C. completely isolated from network thus providing easy management

D. minimum scalability for application delivery

A. Symmetrical configuration is recommended for high availability.

B. Default VLAN 1 can be configured explicitly on an Uplink Ethernet Port or Port Channel

C. Each vNIC can communicate with all the disjoint Layer 2 networks.

D. Ethernet Switching mode must be end-host mode.

E. Appliance port cannot be configured with the same VLAN as Uplink Ethernet Port or Port Channel.

F. Overlapping vlans are supported.

A. The outputs of the debug are redirected to the logging buffer.

B. The outputs of the debug are redirected on a file test on the "log"directory.

C. If you are on a console connection, the outputs are shown after the event occurs.

D. The command doesn't have an effect unless you configure "debug enable".

A. Because Cisco devices transmit BPDUs to the SSTP multicast MAC address on VLANs other than the native VLAN of the trunk, non-Cisco devices do not recognize these frames as BPDUs and flood them on all ports in the corresponding VLAN.

B. The non-Cisco 802.1Q cloud that separates the Cisco devices is treated as a single broadcast segment between all devices connected to the non-Cisco 802.1Q cloud through 802.1Q trunks.

C. Cisco devices connected to the non-Cisco 802.1Q cloud receive these flooded BPDUs. This BPDU reception allows Cisco switches to maintain a per-VLAN spanning tree topology across a cloud of non-Cisco 802.1Q devices.

D. Because Cisco devices transmit BPDUs using the industry standard IEEE 802.1D spanning tree multicast MAC address (01-80-C2-00-00-00), the non-Cisco 802.1Q cloud will seamlessly participate in spanning tree protocol.

E. Additional equipment will be needed to transmit traffic between Cisco devices and non-Cisco 802.1Q cloud direct connectivity is not possible

F. Only layer 3 connections will work between Cisco devices and non-Cisco 802.1 cloud.

A. LACP Port priority default value should always be changed

B. A higher port priority value means a higher priority of LACP.

C. Port priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.

D. Port priority value can be configured between 1 and 65535.

E. LACP uses the port priority with the port number to form the port identifier.

A. They enable automated configuration backup for devices.

B. Local console access is never included in AAA and can be used for access when the AAA servers are down.

C. They make it easier to manage user logins and passwords across devices.

D. They centrally manage user attributes and permissions.